Enjoy Regatta Pointe Yacht Club’s September Social Soiree

Get up, get out, and get down with the Regatta Pointe Yacht Club at the September Soiree on Aug. 27 (6:30-10:30 p.m.).  

Members and non members are welcome to attend.  Cost is $20 for RPYC members and $25 for the general public.  The Riverhouse Reef & Grill is hosting in their beautiful waterfront banquet space (Eagle’s Nest) and catering with their award-winning buffet. 

Come out and socialize with your fellow boaters, and shake it up on the dance.  The attire is business casual. 


Understanding & Working With Sails – Part 7

We’re always looking for useful resources to increase your boating knowledge.  Here is the fifth part of a seven-part series on understanding and working with sails.  Check it out!

Written by 

Sailing and Understanding Sails: Cruising chutes

Today’s Bermudan-rigged yachts have much in their favour, but sailing downwind in light and moderate going is not one of them. Ideally, this endemic shortfall is cured by using a spinnaker, but this lies beyond the comfort zone of many cruising sailors. The answer is a `cruising chute’. This has been developed from the modern asymmetric racing spinnaker and is really a light, extra-full genoa that only attaches at tack, head and clew. It works in airs too gentle for a multi-purpose genoa, and can be set on a very broad reach without a pole. Sailmakers will deliver them complete with a `snuffer’ – a sort of sleeve which rolls down over the sail, spilling its wind miraculously. This removes the worry from using so powerful a tool. In short, a downwind passage in light weather without a chute is like the proverbial day without sunshine.


Understanding & Working With Sails – Part 6

We’re always looking for useful resources to increase your boating knowledge.  Here is the sixth part of a seven-part series on understanding and working with sails.  Check it out!

Written by 

Sailing and Understanding Sails: Shortening Sail

Shortening sail as the wind strengthens is part of the sailor’s everyday life. It is not something to be put off. The process should be as natural as shifting gears in the family car. Not only does carrying the right canvas for the conditions give you a drier ride and increase your chances of arriving with the boat in one piece, it keeps the yacht more upright. As we have just discussed, the less a boat is heeling, the easier she will be on the helm. This benefit is assisted by the fact that the centre of effort of a smaller headsail or a reefed genoa is further forward than that of a larger one. Similarly, a reef in the mainsail moves the leech inboard along the boom. The sails are therefore generating less weather helm than if the yacht were spreading everything she carried. With a sensible awareness of the principles of sail balance in your mind, it isn’t difficult to reduce your canvas in such a way that the boat’s behaviour remains docile.

It would be unwise to generalise about where to begin sail reductions. A masthead cruising sloop will usually set out by tying one reef into the mainsail. This may be followed by one or two changes of headsail before going for the second reef, and so on. A fractional-rigger often reduces the size of her headsail first. A ketch or yawl has a mizzen to consider as well, but the principles remain the same.

The years since the mid-1970s have seen the rapid rise and general acceptance of patent reefing systems. The best of those offered for headsail roller reefing have by now achieved high reliability and are able to reef the sail to a moderate degree without too much sacrifice in shape. Poorer gears produce a dismally reefed sail which looks more like a flour bag than a number 3 genoa. With the canvas rolled away to storm jib size the result is execrable. None the less, all such arrangements give the benefit of instant sail area adjustment. In a short-handed craft this sometimes more than compensates for what is lost in pure performance. No boat must go to sea, however, without making at least some arrangements for the day when the gear fails. The most satisfactory answer is a separate forestay that can be readily set up and to which a storm jib may be handed. Indeed, this produces the best of all worlds because such a jib will invariably set better than the deeply rolled genoa. It can therefore be used routinely for heavy weather sailing. 
Mainsail reefing systems now exist which are way in advance of the old ’round-the-boom’ roller reefing. Such a method was never ideal on the bermudan rig, though it remained in use for decades. By far the simplest and best way to reef the main is with `slab’ reefing, but if you cannot bring yourself to make even that much effort, in-mast and in-boom systems can be bought off the shelf. In-mast gears put considerable weight aloft and add to the awful sum of the rig’s windage. They may or may not be reliable, and a sail built for such a setup will probably have a straight leech with no battens. On a contemporary rig this looks downright sad and it’s certainly less powerful than the elliptical trailing edge of the conventional mainsail. The Spitfire didn’t have those beautiful wings just to look pretty.

Mainsail reefing options therefore subdivide into three choices: in-mast roller, inboom or round-boom roller, and traditional gear for reducing the sail in `slabs’ at the foot. Of the three, slab produces by far the best sail shape; it’s extremely reliable and, in any case, is readily repaired at sea. Mainsails of under 500 sq ft (46 sq m) are easily handled by two healthy adults and can be dealt with singlehanded without major inconvenience. To compromise this vital sail out of laziness or lack of stomach for getting wet seems odd to me, especially when the latest fully battened mainsails and lazy-jack systems make the job of stowing child’s play.

Nonetheless, the roller alternatives do have a place. They help huge yachts to be run without numerous deck-hands. They also enable the elderly or the unfit to keep on enjoying their cruising, but if these options are to be chosen, it’s important to be aware of their limitations in sail shape and, potentially, their unreliability. At least an in-boom reefing system is within reach in the event of failure. Furthermore, the mainsail has a conventional halyard and can always be dropped. Although in-mast systems have improved greatly, they still represent a total commitment to the dependability of the gear. A trip to the masthead in a gale holds little appeal for any of us.


Understanding & Working With Sails – Part 5

We’re always looking for useful resources to increase your boating knowledge.  Here is the fifth part of a seven-part series on understanding and working with sails.  Check it out!

Written by 

Sailing and Understanding Sails:  Hull Balance

In addition to the disposition of her sail plan, a yacht’s helm balance varies depending on how much she is heeling. As she heels to leeward, any tendency to weather helm will increase. Rolling to windward generates lee helm. This makes sense when you consider that the whole outfit is being pulled along by the rig. As the boat heels, the centre of effort of the mast and sails moves outboard. If you dragged the boat through the water by a rope on the end of a beam lashed athwartships across her deck, she would try to swing away from that side. The same thing happens with the rig.

Boats with flat, beamy midships sections such as are found in many high-performance modern cruisers and racers suffer from a more subtle source of heel induced weather helm. As they lean over, the leeward side of the immersed hull becomes rounded to a point of exaggeration. The weather side is correspondingly flattened. The imbalance produces weather helm which, in certain cases, appears suddenly and uncontrollably above a critical angle of heel. You need to watch out for this in such a vessel, particularly if you are sailing in a river on a gusty day, surrounded by expensive moored yachts.


Understanding & Working With Sails – Part 4

We’re always looking for useful resources to increase your boating knowledge.  Here is the fourth part of seven-part series on understanding and working with sails.  Check it out!

Written by 

Sailing and Understanding Sails: Sail Combinations

Una-rigged craft often sail excellently. A single, well-shaped aerofoil set from a lightly stayed or unstayed mast can be shaped with great precision and can be remarkably close-winded. Two notable examples of the truth of this are the Finn dinghy and the North American cat boat. As yachts become larger, a single sail becomes a worse proposition for reasons of handling and of shipping a spar of sufficient proportions to carry it. From time immemorial, therefore, sail plans have been divided.

In addition to the benefits above, split rigs offer two further advantages. Because individual sails are set forward and abaft the centre of lateral resistance (CLR) about which the boat effectively pivots, they can be sheeted so as to balance her steering characteristics. At speeds too low for the rudder to be useful, the sails can even be used to persuade the vessel to point where you want her to go. Secondly, the slot between two sails produces a venturi effect, accelerating the air which is squeezed through it. This raised velocity increases the power not only of the rig as a whole but also of its individual components. Those who doubt that this is happening have only to stand in the slot of a yacht sailing to windward in 15 knots of breeze. Tell them to hang on to their hats, though. It’s breezier in there than they’d ever have believed back in the cockpit. 

As skipper, you have the balance of the boat’s rig at your fingertips, and assuming that she is well designed, there is plenty you can do about it. The yacht should be easy and light to steer, showing a gentle tendency to turn into the wind if left to her own devices. If she has too much mainsail on and only a small jib, a sloop will want to round up. The result is weather helm. This tires the unfortunate who must steer, as well as slowing the vessel down through the drag of the rudder. The dreaded lee helm, on the other hand, is the lot of the sailor whose boat is carrying too much canvas forward and too little aft.

Lee helm is a dismal condition. It makes manoeuvring difficult, steering frustrating, and it has a debilitating effect on the yacht’s capacity to sail close to the wind without making excessive leeway. A touch of weather helm holds the rudder a degree or two to leeward, which diverts the flowing water, just enough to help the keel lift the vessel in opposition to the sideways forces. Lee helm achieves the converse effect.


Understanding & Working With Sails – Part 3

We’re always looking for useful resources to increase your boating knowledge.  Here is the third part of seven-part series on understanding and working with sails.  Check it out!

Written by 

Sailing and Understanding Sails: Shaping the Mainsails

As in a headsail, mainsail camber is largely controlled by luff tension. However, sails on boats with any pretension to performance generally also offer a clew outhaul. The effects of this will extend approximately to the lower third of the sail. Haul it out to flatten the sail as the breeze fills in. 
A mainsail that is set behind a genoa will emphatically not require a hard entry. Such a form will often result in the backwinding of the main luff when the boat is closehauled. Instead, a gentle curve aft to a maximum camber virtually in the centre of the sail will work well if the boat is masthead rigged. The more powerful sail of a fractional rigger should carry its maximum camber somewhat further forward, but still with a flat, gentle entry.

Mainsail twist is highly controllable on a modern yacht. Leech tension, the essential element, is determined by the mainsheet when closehauled. With the kicking strap (or kicker, or centre boom vang) let off, juggle the sheet tension until the top batten of the sail lines up with the boom when viewed from directly underneath. There is no need to lie in the bottom of the cockpit, a glance will suffice.

Once you have the twist you are after – and if the sails are well cut, the leech of the main will now sweetly follow that of a well-trimmed genoa – the mainsail’s angle of attack can be determined by using the mainsheet traveller, so long as the wind is well forward of the beam. This means in practice that when you are beating or close-reaching you shape the sail with halyard, outhaul and sheet, then trim it with the traveller. If you are far enough off the wind to want to ease the sheet, set up the kicker to maintain leech tension when the sheet can no longer supply it.

On a race boat, the powerful kicker may be brought into service even closehauled to help flatten the sail. Such fine tuning is a waste of effort on most cruising mainsails, but the basics should never be neglected. I’ve heard people complain along the lines of `All this sail shape nonsense is for the boy racers. Who cares about Y knot?’ I do, for one. At 6 knots it is worth 6 miles over 24 hours. To be an hour later than you might have been could lose you a tide, resulting in a further three hours’ delay. It may also be the last straw for a fatigued crew, causing a fatally bad decision in the face of a rising gale which you would otherwise have missed. Or you might merely get in after the shops have closed.

Whatever the result, not to give your boat her best chance to perform well is unseamanlike. You don’t have to thrash a boat to extract that extra Y knot, yet carried to its logical conclusion, 6 miles lost in a 24-hour passage is the best part of two days wasted on the average ocean crossing, though in fairness I have met people who don’t press on because they seem to like it out there.


Understanding & Working With Sails – Part 2

We’re always looking for useful resources to increase your boating knowledge.  Here is the second part of a seven-part series on understanding and working with sails.  Check it out!

Written by 

Sailing and Understanding Sails: Shaping the Headsails

In most boats, the primary tool for headsail camber control is the halyard winch. Some traditional craft are equally well served by a tack downhaul, but whatever method is employed, the crucial feature of the sail at any given time is its luff tension.

Hoist the sail, then steer the boat on, or nearly on a closehauled heading. Now look up at the mid-part of the sail. If it has a ‘go-fast stripe’ your task is made easier. If not, you’ll have to judge its shape by looking at the seams. The camber should swell out to a maximum 35-40% of the way aft from the luff. If it is too far aft, tension up the halyard and watch the draught move forward. If the luff is too `hard’ (ie, the camber is too far forward), slack away a few inches and keep looking.

If the sail seems susceptible to this treatment, check it again once your boat speed has built up. The apparent wind will now be greater and the sail may require some adjustment. It’s important to do this with your fully open roller reefing genoa as well as a hanked-on sail.

As the wind picks up, keep hardening the luff until your efforts to maintain a good camber become fruitless. The sail should now be overpowering the boat if the sailmaker and the designer got their sums right. Change it for a smaller one, which should also be flatter cut, or roll some away.

The converse of keeping your sails reasonably flat as the wind hardens is that a sail can sometimes be set up to be too shallow-cambered. It will then lack the power to drive the boat in light airs. If the sail seems lifeless, ease the halyard, and the sheet too if necessary, so as to power up the canvas.

Attention to the luff of the sail may cause the leech to require service. The leechline, if fitted, is a light piece of small stuff sewn into the trailing edge of the sail. It should be gently ‘tweaked’ just far enough to stop the leech beating, and no further. Too much tension causes a hooked leech, which is hateful to behold. If the leech is already hooked, slack away the line as far as the sail will let you.

The twist of a headsail is determined mainly by the position of the sheet leads. Most boats have these on sliders. If yours doesn’t, the sail must be cut to the position of the fixed leads. 
Sheet-lead positions are crucial. When the helmsman brings the sail a little too close to the wind from closehauled or a close reach, the luff should lift evenly all the way up. If the bottom of the luff lifts first, the lead is too far forward, making the leech too tight so that the sail is not twisting enough. If the top goes first there is too much twist, caused by the lead being too far aft. The best position can only be found by experiment, but luff ‘tell-tales’ are a tremendous help. If you don’t have any, install them now. All you need are three 8 in (20 cm) lengths of wool pushed through the sail with a sail needle, about 6 in (15 cm) abaft the tuff (in a 35-footer) and knotted on both sides. The windward ones will always flick up just before the sail lifts. If the leeward ones go dancing they tell you without room for argument that the sail has stalled either from oversheeting on a reach, or because the person steering the boat to windward is driving her to leeward of her best course.


Understanding & Working With Sails – Part 1

We’re always looking for useful resources to increase your boating knowledge.  Here is one part of seven-part series on understanding and working with sails.  Check it out!

Written by 

Sailing and Understanding Sails: Part 1 - Efficient Sailing

Sails today are very different from their ancestors in the period before the polyester revolution. Shape has always been the most important factor in sail efficiency, and time was when you chose your most suitable canvas for the conditions, pulled it up and sheeted it in. Some cruising sails are still made like this. They work well enough, but the cloth from which they are cut often means that their performance potential is nowhere near that of a modern sail whose geometry can be modified to suit the wind and sea. Such equipment has worked its way into cruisers following the lead set by racing yachts, whose hi-tech vanguard have now moved on to cloths of such sophistication and stability that the shape cut into their sails is barely compromised until they literally burst.

The maximum camber of a sail should be somewhat forward of the middle of its cross-section. In practice this varies to a degree with what sort of sail it is and how hard the wind is blowing. The power of an aerofoil depends upon its depth of curvature, so a baggy sail will drive you along in light airs far more effectively than a flat one. As the breeze hardens, the power of the fullcut sail will become too great for the boat. It must then be flattened or reefed, if either is possible; or changed for a different sail if not.

This requirement is underlined by the fact that as the wind increases, a sail naturally becomes fuller and the point of maximum camber is blown aft towards the leech. Both these results are the opposite of what is desirable, and something must be done to mitigate them.

In addition to the question of camber control, there is also the matter of twist. Most sails twist away from the wind in their upper sections. This tendency is built into them deliberately and can be controlled so that it works to your advantage.

Twist is a shut book to many sailors, but to ignore it will measurably compromise your boat speed. The reason for its importance is this: wind blows more strongly aloft than near the deck, because surface friction with the sea slows it down. When a boat sails along, the wind she actually experiences is a composite known as apparent wind. She may be powered by a true wind from abeam, but she is making a ghost breeze from dead ahead in an equal and opposite direction to her own progress through the flowing air. This phantom combines with the true wind to generate the actual breeze across the sails. The apparent wind which they form comes from further ahead and is stronger than the true wind, so long as it is not blowing from well abaft the beam.

Clearly, the faster the true wind for a given boat speed, the less will be the interference caused by the boat’s movement. Because the true wind aloft is a little stronger than at deck level, the apparent wind up there is somewhat more `free’ than the air lower down. If the upper part of the sail can be twisted to take advantage of this, its resultant force will produce a larger forward component than that being delivered by the lower section of the same area of canvas.

Furthermore, the whole of the sail will be setting cleanly, with no part either lifting or stalling. 
In the case of a fractional rig, the upper section of the mainsail cuts undisturbed air, while the lower parts receive their wind already bent further aft by the headsails. Twist control is vital if the top of the sail is not to be stalled completely.

Too much twist can generate a fearsome loss of power if it is allowed to go unchecked while you are reaching on a windy day. The boom kicks up in disgust, while the upper third of the mainsail dumps its air unceremoniously to leeward over its tortured leech.



Regatta Pointe Marina Guide to Boat Terminology

Boat isn’t hobby; it’s a culture.  Regatta Pointe Marina (located between Bradenton and Palmetto, FL on the Manatee River) embraces the culture of boaters unlike any marina in the region. And that include boat terminology. 

At Regatta Pointe Marina, we speak boaters.  If you want to be fluent in the language of the water, get to know this guide to boating terms.

Regatta Pointe Marina Guide to Boat Terminology:

ABAFT - In the direction of the stern, or the rear of the boat

ABEAM - On a line that forms a right angle to the ship’s keel

ABOARD - On board (of a ship or a boat)

ABOVE DECK - On the boat’s deck

ABREAST - By the side of, next to or side by side

ADRIFT - Floating at random, not on the towline.

AFT - Near or in the direction of the stern of the boat

AGROUND - When the bottom of the boat touches or lodges on the ground.

AHEAD - In front of; to go in advance

AIDS TO NAVIGATION - Road signs used on the waterway, they help indicate the safety level of water

ALOFT - Above or on top of the boat’s deck

AMIDSHIPS - In the middle or center of the boat

ANCHORAGE - Where a ship anchors or a suitable place to anchor

ASTERN - Towards the back of the boat

AWEIGH - When the anchor is raised and off bottom of body of water

BATTEN DOWN - To secure or strengthen the hatches and objects on the deck and hull of a boat

BEAM - The boat’s width

BEARING - The direction of an object as determined by a compass

BELOW - Down below, beneath, or under the deck

BILGE - The broadest width of the bottom of the boat

BOAT - A small open vessel or watercraft.

BOAT HOOK - A pole that has a metal point and hooks that is used to maneuver logs, or retrieve objects that have fallen overboard

BOW - A boat’s front section

BOW LINE - A rope that is used to tie the boat to a dock; it has a loop spliced at one end

BOWLINE A special knot that is used to create a temporary loop; there are several variations for forming a bowline

BRIDGE -Where the ship is steered or controlled.

BULKHEAD - A partition that is used to separate compartments on a boat

BUOY - A floating device used for marking locations or other hazards in the water

BURDENED VESSEL - Also referred to as Give Way; the vessel that must yield to another vessel

CABIN - The compartment used for crew members or passengers

CAPSIZE - When a boat upsets or overturns

CAST OFF - To untie or let go.

CHART - A marine map

CHINE - The line where the sides and bottom of a flat or v-bottomed boat intersect

CHOCK - Fittings used to pass ropes or mooring lines

CLEAT - Fittings used to hold ropes or lines securely

CLOVE HITCH - A temporary knot used for securing a rope or line to a piling or spar

COURSE - The direction a boat is steered.

CUDDY - A small cabin on a boat

CURRENT - The course in which the water flows

DEAD AHEAD - Straight ahead

DEAD ASTERN - The position behind the boat

DECK - Floor like coverings of the compartments of a ship

DINGHY - A small rowboat or open boat

DOCK - A pier or wharf

DRAFT - Depth of water necessary to cause the boat to float

FENDER - A cushioning device that is used to prevent the sides of a boat from damage

FLARE - Where the boat’s sides spread outward, near the bow of the boat

FLUKE - Where the anchor fastens to the ground

FOLLOWING SEA - A sea swell

FORE-AND-AFT - The length of the boat from the bow to the stern

FOREPEAK - Used for storing cargo, a small section within the bow of the boat

FORWARD - Toward the front of the boat

FOULED - The encrusting of foreign matter or debris on the hull of a boat

GALLEY - The boats kitchen area

GANGWAY - The side of the boat used for the boarding of passengers

GEAR - Nautical equipment such as ropes, tackle, etc.

GROUND TACKLES - The anchor and its accessories

GUNWALE - The top of a boat’s side

HATCH - Located in the deck, it is an opening that has a secure cover

HEAD - A nautical commode (toilet)

HEADING - The direction that the bow of the boat is pointed in

HEADWAY - The progress the ship makes as it moves across the water

HELM - The wheel that steers the ship

HELMSPERSON - The one who steers the boat

HOLD - A compartment used for storing cargo, located below the deck

HULL - The boat’s main body

INBOARD - The inside of a boat

INTRACOASTAL WATERWAY - ICW: A body of water that is used for boats to travel upon

JETTY - A structure that extends or jets out from the shore

KEEL - The line of the boat that extends through the center; also a barge

KNOT - A unit of speed that is understood to mean per hour (6080.27 feet)

LATITUDE - The distance north and south of the equator; latitude is measured in degrees

LEEWARD - The direction in which the wind blows

LEEWAY - The direction a boat drifts to leeward of the steered course

LINE - The rope or cords that are used on a boat

LOG - A record of nautical activities

LONGITUDE - Distance measured in degrees that determines east and west from the Prime Meridian

MIDSHIP - The middle of a ship; between the bow and stern

MOORING - Anchors or fastenings used to secure a boat

NAUTICAL MILE - The unit used for measuring nautical navigation; one nautical mile equals 1,852 meters or 6,076 feet

NAVIGATION - The act of passing over water in ships or boats

NAVIGATION RULES - Steering and sailing rules that govern how boats and ships pass over water

OUTBOARD - The outside of the hull of a boat

OVERBOARD - The place located outside the side or edge of a boat

PIER - A wharf or structure that is used as a landing place

PILE - A pole made of wood, stone, or metal used to support a pier.

PILING - Used for driving piles; or a structure composed of piles

PILOTING - Coastal navigation that utilizes soundings and buoys

PORT - Place in the water that is used to provide shelter for boats

PRIVELEGED VESSEL - A vessel that has the right of way according to Navigation Rules

QUARTER - The upper sides of a boat; between the stem and the mast

RODE - The line or rope attached to an anchor

RUDDER - Used for steering a boat; a hinged plate made of fiberglass, wood or metal that is mounted to the stern

RUNNING LIGHTS - Required lights that are displayed on a boat between sunrise and sunset

SATELLITE NAVIGATION - Navigation that uses satellite transmission via radio waves and equipment located on the boat

SCREW - The propeller on a boat

SCUPPERS - Holes in the side of a ship, used to allow water to drain.

SEAMANSHIP - The skill of navigating a boat or ship.

SEA ROOM - A location in sea where there is no obstructions; the space that is safe for navigating a boat or ship

SEAWORTHY - A boat that is deemed fit and safe for navigating or passing over water

SECURE - Tighten, or make fast

SET - To put forth in a specified direction

SLACK - To loose, not secure, or fast

SOUNDING - The measurement to determine the depth of water

SQUALL - A brief windstorm; usually comes on suddenly and is accompanied by either snow or rain

STARBOARD - It is the right side of a boat when one is facing forward

STEM - The part of the bow that extends the most forward

STERN - The part of a boat or ship that is in the rear

STERN LINE - A line or rope, used for docking that extends from the stern

STOW - To arrange or place items where they belong

TILLER - A lever that is used for steering a boat’s rudder

WAKE - Waves, path, and the tracks left when a boat passes over water

WATERLINE - The line on the hull of a boat used to determine the depth a boat sinks

WAY - The movement of the boat as it passes over water: may be leeway, headway, or sternway

WINDWARD - Of the side that is exposed to the wind